| ¡¯Straight-Through
Wire Drawing Machines (HSRD) |
| |
| ¡û
Application¡G |
| |
Wire-drawing
for various materials including stainless, low carbon
steel, copper, and steel shrouded with copper. |
| |
|
|
| |
Area
Reduction¡G
16~35%. |
| |
Water
Consumption¡G
200~300 L / Min Cooling |
| |
|
Water. |
| |
Voltage¡G
Adjustable up to request. |
| |
Voltage¡G
Adjustable up to request. |
|
|
Color¡G
Light Blue or up to request. |
| ........................................................................... |
|
| ¡û
Operation
¡G |
¡û
Safety¡G |
| |
1.
Step Motion: Single Block Step or |
| |
|
Multiple
Block Step. |
| |
2.
Single Block Motion. |
| |
3.
Continuous Motion: Option: Sectional |
| |
|
motion
in the front or rear blocks. |
| |
4.
Rotations: Forward or Backward. |
| |
5.
Automatic Stop upon the pre- |
| |
|
specified
length of wire-drawing. |
|
|
| 1.
Safety Guards: Machines are screened by |
| |
pieces
of steel grids for protection of workers. The machines
cannot be activated until a complete seal by the
steel grids. |
| 2.
Wire drawing discontinuity detected and |
| |
capability
to pose a full stop.
|
| 3.
General Stop Devices. |
| 4.
Emergency Stop Devices. |
| 5.
Automatic Braking Devices. |
| 6.
Wire Discontinuity Sensors. |
| 7.Inverter
warning device with ability to |
| |
automatically
stop machine running. |
|
|
| ................................................................................................................................................... |
| ¡û
Components
¡G |
| 1.
Motor¡G |
| |
A.
Power Transmitting: Belt transmission between the |
|
| |
|
motor
and gear box. |
| |
B.
Cooling: Low noise fan. |
| |
C.
Speed Control: Variable in compliance with control |
| |
|
volume. |
| 2.
|
Reduction Gear Box¡G |
| |
A.
Gear or Planetary gear type. |
| |
B.
Cooling and lubrication by circulating oil. |
| 3.
|
Block¡G |
| |
A.
Surface Treatment: Tungsten Carbide. |
| |
B.
Cooling: High pressure water injection inside the block. |
| 4.
|
Die¡G |
| |
A.
Cooling: Closed-cycle water cooling. |
| |
B.
Lubrication: Dry or wet lubrication: using pressurized
oil to make the wire coated with a layer of |
| |
|
oil
for a complete lubrication. |
|
| |
C.
Input angle control: Up and down; Left and right. |
| 5.
Wire tension control: The use of pressurized air tank
enables the |
| |
adjustibility
of the wire tension. |
| 6.
Dimension tuning of the wires: Diameter and straightness. |
| 7.
Supporting equipment: The rollers used to initiate wire
drawing. |
| |
|
| ................................................................................................................................................... |
| ¡û
Options ¡G |
| |
A.Rotating
Die.
B.Wire damage detection.
C.Peeling machine before the first block. |
|
| ................................................................................................................................................... |
| ¡û
Specification
¡G |
| Model
|
Block
Number
|
Block
Dia.
(mm)
|
Length
(mm)
|
Width
(mm)
|
Height
(mm)
|
Power
(HP)
|
Inverter
(HP) |
Application
wire
Dia.(mm) |
Final
Block
Speed (Max.) |
| Input |
Ouput |
| HSRD600-7 |
|
600 |
1320*7 |
1775 |
1500 |
45 |
50 |
ø5.5 |
ø2.0 |
500m/mim |
| HSRD400-9 |
9 |
400 |
1100*9 |
1420 |
1470 |
15 |
20 |
ø2.6 |
ø1.0 |
600m/mim |
| HSRD300-9 |
9 |
300 |
860*9 |
1420 |
1470 |
7.5 |
10 |
ø1.0 |
ø0.4 |
600m/mim |
|
| Note:The
models with different design specification from the above can
also be provided. |
| |
|
| |
| |
| |
| ............................................................................................................................................. |
